How to Do a Door Lock Change

The change of your door lock is an easy and inexpensive way to increase the security of your home. The process is not for everyone. It requires a certain amount patience and expertise.

The cylinder is located within the knob's body. The cylinder is what identifies the key once it's inserted into the lock.

Removal of the old lock

First, you must remove the lock that was previously in place. It is a fairly simple process, but it is important to keep certain things in your mind. Make sure your new double glazing window lock repairs is compatible with your door. This will ensure that it fits securely, and doesn't leave a gap in the deadbolt or latch.

After you have removed the latch plate, look for two screws or bolts on the inside of the casing that hold the casing and the halves of the lock. Remove these screws using a screwdriver and then pull the lock off the door. If you have a mortise lock, there could be a set screw at the base of the handle, which binds it to the spindle. Use a screwdriver to unscrew the screw, and then take out the doorknobs.

It is also recommended to remove the latch and deadbolt plug from the hole in the door jamb. Install your new lock. If you are replacing a mortise you must determine the distance between the lock case and the door edge to ensure that the new lock is a good fit.

You might want to change your lock for a variety reasons, for instance, if you suspect that someone else is holding the key or you've got an incoming roommate. In any event, you could save money by taking the lock off yourself rather than paying a professional to do it. It's much simpler than you think and can be completed in just a few moments.

Begin by getting rid of the handle and trim from your door. Then, pry the trim away using a flat screwdriver. It should be possible to pull off the majority of it. In certain cases you might be able to remove the handles completely. Next, search for a pinhole on the inside of the handle and insert a straightened clip into it. This will trigger the release mechanism, which allows you to remove the handle. Look for a small tab that is located inside of the lock and push it with a flat screwdriver. Once the spindle is removed, you can remove the cylinder and the housing.

The process of selecting a new lock

When it comes time to pick the right lock for your home you have a variety of options. Take a look at various kinds of locks, and choose one that is compatible with the style of your door. Think about the backset (the distance between the door's edge and the center of the hole for the lock) and the cross bore (small hole that runs along the edge of the door frame). Also, be sure to choose a Window Lock Replacements that will fit the door thickness and swing.

The American National Standards Institute and BHMA have graded all door locks to give an idea of their longevity and how difficult it is to pick them up or disable them. A grade 3 lock may be perfect for a quiet apartment building in a rural area, whereas locks that are grade 1 may be more suitable for the busy streets near a storefront.

Most smart door locks require digital code to open. If you're worried about hacking or other security concerns, consult with an expert locksmith or your local police department for advice.

Replace the cylinder

If the cylinder of your door lock is broken or damaged you can repair window lock it in a matter of minutes by completing a do-it-yourself project. It is important to select the correct cylinder and follow all instructions. The first step is to take off the knob or handle should there be one, then unscrew the trim around the base of the lock cylinder with the aid of a screwdriver. After the trim has been removed, you can take off the screws holding the cylinder in place using the flathead. The cylinder is then gently pulled out of the door.

Before installing the new cylinder, make sure it's the correct length for the door you are using. With a tape measure, determine the distance between the cylinder's center and the right and left sides. Buy a new cylinder that has the same measurements. This will help prevent cylinder snapping, which can happen when the door is kicked out or when the key gets stuck inside.

If you have a suitable replacement cylinder, place it into the door and turn the key. This will align the cylinder with the carriage which is located usually on the outside of your upvc window lock repair cost. You can then loosen the set screws which should be a couple of turns in the head. If there is a screw located on the edge of the case that is holding the door, you will have to loosen it.

You can replace the cylinder that was used to lock your old lock with the new one by inserting it into the case, and then tightening the set screws. The process of reinstalling the component that connects the cylinder to a lock indicator stem is also important. This can be done by pulling three tabs at the back of the cylindrical using needle-nosed pliers. Attach the smaller bracket to the cylinder's back. Then, you need to install the strike plate and latch plate, as well as the retaining ring that is attached to the top lock the cylinder.

Installing the new lock

Begin by measuring the door's width if are replacing a lock that is already in use. Most residential locksets are designed to fit a door thickness of 1 3/8 to 1 3/4 inches. If your door is thicker than 1 3/8 to 1 3/4 inches, you'll require an extra thick door kit. This would include longer screws and either an extension for the spindle or a longer tail piece for door knobs.

Most locks come with a comprehensive instruction booklet that will assist you in installing the new hardware. Be sure to read the instructions thoroughly before starting the process to make sure that you are following all of the necessary steps. The manual will give you a clear idea of the amount of skill that is required to finish the task. It is possible to ask a person who has experience changing locks for assistance if are changing a lock the first time.

Before installing the new lock, it's an excellent idea to put tape over the openings of the old hardware. This will stop the screws from falling out of the holes and will protect any tile you might have put in the area. This will also protect your tiles from damage caused by rust, dirt and grime. SECURAM Touch includes a strip of masking or gaffer tape, but you can use any tape you have.

Once you've removed the screws holding the interior portion of the lock section to the exterior side immediately, pull it back. It is important to do this as quickly as possible to avoid the lock from closing itself in a way that could end up damaging the mechanism.

Install the new latch bolt in the upper cross bore of your new lock, if it comes with one. Be sure to put it in the correct position that is usually indicated by an illustration on the faceplate. Then, screw the latch plate onto the bolt.

Attach the deadbolt to the jamb of the door. Test the deadbolt a few times by throwing it to ensure it is extending into the strike plate. If you're using an electronic smart lock, be certain to follow the instructions for programming it. This requires downloading an app, registering your email address, confirming your identity, then accessing the wireless network to connect your device.