Patio Door Lock Repairs

Over time, patio doors undergo wear and tear that could lead to locks that fail. There are a few simple steps you can take to restore the security of your uPVC door.

These simple fixes will ensure your home is secure, whether you realign the lock or clean the locking mechanism.

Clean the Lock

While patio doors are an excellent way to bring the outside in and keep out the elements but they can also pose security risks in the event that your lock isn't operating as it should. Over time, wear, tear, hot and cold weather, dirt, and debris can cause your patio door lock to become difficult to operate. Fortunately, with a little maintenance you can ensure that the locks on your patio door always perform correctly.

To begin with, it's important to clean the lock of your patio door lock repair (relevant web site) door and all its moving parts. This will help to remove any coatings or dirt that could be preventing your lock from working correctly. Start by wiping all the moving parts of the lock for your patio door with a wet cloth. Then you can use a scouring paper or rough damp cloth to scrub the dirt-infested areas of the door frame and frame. You should then wipe down the entire lock with a dry cloth to remove any remaining dampness and allow it to air dry prior to making use of it again.

If you have an exterior door that is fitted with a pin tumbler latch mechanism it is possible to lubricate the lock by applying powdered graphite to the key or using an lubricant based on Teflon like WD-40 Multi-Use. This type of lubricant is able to be applied easily and doesn't dissolve over time. If you are unable to find the correct lubricant for your lock, make use of a pencil with a more of a thicker tip. Insert the pencil in the lock, then shake it around to distribute the graphite.

Sliding patio door tracks also require regular maintenance to keep them free of dirt, dust and other debris. These tracks are especially susceptible to ice, snow, and other debris that can cause them block or become stuck. This can make it difficult for your patio door to open and close.

You can clean the track rails and rollers on sliding patio doors by removing damaged or dirty weather stripping. Clean it, then replace it. The same is true for rollers on patio doors, which can be cleaned and sprayed with non-stick lubricant in order to allow them to move freely.

Lubricate the moving parts

uPVC French Doors, similar to sliding patios, operate by using 3 to 4 or sometimes 5 points locking mechanisms. This includes the lock cylinder and handle that is operated with a key. These doors require maintenance, the lubrication of moving parts. This can be done with the use of a thin oil but not WD40. It should be done every year, at a minimum.

If the hinges aren't causing the problem, it could be that the door is misaligned. It could be rubbing or catching the hole of the strike plate in the frame. The solution is to remove the strike plate and use an abrasive chisel to increase the size of the mortise it sits in. This allows the latch to fit properly in the hole and prevents getting caught or rubbing against the frame.

While the cylinder is out of the way and out of the way, measure its width using a book or piece of wood that fits into the gap of adjustment screw above the lock. The outer dimension is the distance from the outside of the door to the middle of the cylinder, while the inner dimension extends from the center of the adjustment screw to the end of the cylinder.

Check the width of the lock.

If your patio door repairs near me door latch isn't able to turn even after oiling and cleaning, it's possible that it's not aligned with the strike plate. Check to see if the door is properly balanced and if the hinge screws are secure However, in many cases shifting the strike plate up or down could fix the problem.

Oftentimes, the problem occurs when the lock's strike is too small for the latch to properly engage. In this instance you'll have to increase the hole with either a hammer or chisel, and then test the latch to ensure that it connects to the strike plate without rubbing against or catching on the frame of the door jamb.

Before you purchase a replacement lock, it is important to determine what kind of mortise lock you currently have. This can be done by looking at the faceplate on the lock and determining if it is square or round. Examine each screw hole in the existing lock and note their dimensions. This will assist you in finding an alternative lock that is the same width and will fit perfectly into your existing hole.

In addition to identifying the mortise lock that is currently in use, you should also examine it for any scratches or bends that may need repairing. A damaged or bent latch is more likely than one that has frequently used to break. Replace the lock if you notice indications of damage.

Once you've identified the type of lock replacement you need It's time to start the actual repair. The old handle and spindle should be removed from the doorway to the patio. Install the new handle. Begin by installing the interior handle. Align it with the spindle and then secure it in position using two screws or bolts. Once the handle in the interior is installed, you can install the handle that is outside and screw it into place as well. After you've completed the steps then you can test the new handles to make sure they open and close easily and that the latch locks properly with the strike plate.

Make sure the door's strike is checked

The strike plate and door latch are two components that work together to secure the door. If they are not aligned properly and the latch doesn't latch the door properly. Fortunately, this problem is usually easy to correct.

First, check the strike plate's receiving holes to ensure that they are clear of obstructions such as dirt or plastic plugs. Then, loosen the keeper screws that keep the strike plate in place, allowing it to move vertically, but not removing it from the door frame. Adjust the strike plate so that it aligns its holes for receiving with the latch hooks of the door latch. After the strike plate is adjusted then tighten all screws, and check whether the door closes smoothly.

Door strike plates can be a bit difficult to access for homeowners with sliding patio door repair service near me doors, but they're crucial for locking and unlocking your door. These plates are usually located on the top and bottom of the door jamb, which is where they are used to support the door's latch. The door latch slides into this strike plate and creates a seal. If the strike plate is damaged or rusted, or if it is not installed correctly the latch may not properly lock the door.

One of the most common reasons for a patio door lock to stick or not close is a misalignment between the latch and strike plate. This can be confirmed using the "lipstick" test. Apply a little lipstick along the edge of the deadbolt, then cover it with masking tape. When you shut the door, the lipstick will leave a mark on the tape, showing exactly where the latch contacts the strike plate. If the mark is too low or high it is possible to adjust the strike plate.

If your patio door locks for sliding are not working properly, they can keep your home secure from intruders. You must fix this problem as soon as possible. Follow these steps to repair your patio door lock and restore it's function.